SOLVED: Can i fix a brake line with out have to replace

Detail: 1989 nissan d21 four wheel drive some body cut the brake line at the rear of the truck where it run from the top of the rear end back to the master cylinder and they replace a rubber hose and clamps so when press the brake pedal fluid come out from around the hose is there a quick way to fix it?
Detail Question SOLVED: Can i fix a brake line with out have to replace

Solution: Make up a new copper pipe and fit the olives to each end. When fitted use the clamps to hold it in place. , Hi, a 6ya Mechanic can help you resolve that issue over the phone in a minute or two. Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US. click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need. Goodluck! , if the booster is bad the pedal would be hard sounds like the e-brake is stuck take off the drums and make sure the arms are all the way back then did you adjust the rear brakes after changing the shoes , possibly new master cylinder is defective , What happens is if you have a bad front wheel bearing when you brake that wheel will turn in or out,when this happens it throws the four wheel alignment out and since this is a solid rear axle,it's forcing it to flex on the suspension,wich could cause the rear tires to bite on the outside edge of one tire and the inside edge of the other,thats one possible the other would be that the rear brakes are are not slowing the wheels evenly causing the same issue.I saw this problem with a bad front wheel bearing on a Nissan Pathfinder but not as pronouced due to the independent rear suspension. Check the front wheel bearings,which of course will mean getting the calipers off the rotors,and then check for any movement in the rotor,if there is check the hub nut,if it's loose tighten it and check for play in the rotor if there is still play that's going to be caused by a bad bearing.You can check the braking in the rear with a simple spring scale(like the ones used for fishing),with the wheels removed have someone apply enough pedal pressure to just engage the brakes but still allow movement attach the scale hook to a wheel stud and pull until it starts to move and note how many pounds of pressure it takes to move the hub.If it's uneven chech your adjusters and even them if needed and then retest,if still uneven you'll need to bleed them again.As far as the dark black substance in the fluid I would say you may gotten a contaminent in the fluid.Brake fluid gets kind of a rusty reddish residue when it breaks down.If I missed anything or you need clarification don't hesitate to ask I'm home all day.Hope this helps solve your problem. , i try to help you, firts refill brake fluid container,open purge valve in one wheel front only,wait few minutes when drops fluid, close this valve and open other wheel, same procedure, finally repeat this in each 4 wheels , do you have a self bleeder kit? first off, you have to bleed the master cyl back into its self and the combination valve before you go to the wheels. when you do that, I think you will find that you have air in the lines. disconnect both brake lines from the master cyl and put the bleeder kit fittings on the master cyl, then put the rubber tubing with the kit on the fittings and submerge it in the brake reservoir. make sure its full. then pump the pedal until you get a hard pedal. if that is the case, reconnect the lines to the master, then have an assistant pump up the brake pedal with the engine off, and bleed the combination valve which should be connected to the master by steel tubing. pump it up, then hold it down, and crack the fittings loose, one at a time until the pedal goes about half way down, but do not release the brake pedal until the line is tight again, otherwise you will **** air in the lines. after you do all that, go to the farthest caliper or wheel cylynder from the master and bleed that with the same technique,and dont release the pedal until you close the bleeder screw. unless you have a major prob, this will work.

By entering you agreed with our Terms of use and Privacy Policy.If you do not agree, please do not use this service or you will face consequences.
This site powered by Express JS, node.js, MongoDBand advanced javascript algorithm include all npm modules
Copyrighted © 2015